Learn Watch Movement Replacements | Watch Repair Education | Esslinger.com | Esslinger Watchmaker Supplies Blog Longines Watch Price

How to Replace a Watch Movement

Posted by Esslinger Staff

When a watch stops working it can be worrisome to people to not be able to tell the time or perhaps because the watch is a heirloom piece. First you must determine whether the watch movement inside that has failed is a mechanical or a quartz movement. There is sometimes no easy solution to fixing the failed movement. When you have a watch that has an older mechanical movement, parts can be very difficult or impossible to find and replacing the original movement with a quartz electronic movement is sometimes the only solution. If the inside of your watch has been damaged beyond repair, (by water damage or the watch has had a hard hit and it is not working) replacing the movement may be the only solution. Make sure that the problem is not just a dead watch battery or an automatic watch that has not been wound up and you could save yourself extra work.


In this article, you are going to learn how to identify quartz watch movements, along with selecting a replacement and then completely replacing it.


Quartz vs Mechanical movementQuartz and Mechanical

You can replace a mechanical movement with a quartz movement or change a quartz movement with an inexpensive generic or factory direct movement without problems. If the original watch movement has additional features including a day/date window or a chronograph with several mechanisms to show the seconds, year, moon phase, or stop watch, you will possibly lose some features if you do not find a direct matching replacement movement. Sometimes the movements are discontinued due to their age, but you still can get parts. This article will cover the situation where you cannot clean the old movement or order replacement parts like a coil or a circuit to make your favorite watch work again.


If you have a name brand watch like Longines, Seiko, Citizen, Pulsar, Lorus, Bulova, the generic direct matching movement could be obtained and the price might be actually lower than buying the original manufacturers movement or replacement parts and fixing the watch.


You will need some watch tools to help work on small mechanical and electrical parts of a watch:


  • Movement Ring Assortment
  • Watch Dial Adhesives
  • Digital Caliper 100mm / 4″
  • Hands Free Magnifier (OptiVisor)
  • Eye Loupe Magnifier
  • Watch Screwdriver Set
  • Watch Battery Tester
  • Brass Handle Pin Vise
  • Non-Magnetic Tweezers
  • Loctite Threadlocker
  • Flush Side Cutter Pliers
  • Needle files, Medium
  • Watch Back Opener Knife
  • Movement Holder
  • Case Holder F/ L-G Case Wrench
  • Watch Opener Case Wrench Waterproof or
  • LG Case Back Opener Wrench
  • Watch Hand-Remover
  • breitling navitimer wereld63;">Watch Hand Press


Replace a Watch MovementOpen the Back

  • A screw off watch back will have large notches around the edges of the back of the watch. Use a Case Opener wrench and Case Holder. Set the watch in the case holder and unscrew the back… Be careful – there is a gasket between the case and the back that needs to be replaced if you damage it.
  • Another type of screw off watch case back has the notches cut out all around the case back. These are commonly seen on Swiss Army and Baume Mercier. For this type of case back removal you will need a case holder and watch case dies or a Watch Case Opener.
  • Pressure fit watch back: The second type of watch case back is the pressure type. It is plain and smooth and we intend to leave it that way when we finish. Many watches with this type of back have a small dent or notch on the case back which is the place you will want to put your watch opener knife.
  • 4 screws watch back: The third most popular watch case back has 4 screws holding the back on. It can be any kind of watch material, metal case and metal back, plastic or rubber case and metal back, plastic case and plastic back, and so on. You will need to determine if you need Phillips head screwdrivers or a straight edge. Choose the right screwdriver for the right screw. You don’t want to strip the head of the screw, and remember that there will be a gasket that you will have to deal with, so be careful.

See our Guide: How to Open a Watch Back



MovementReplace-remove_stemRemove the stem

Locate the screw to be loosened if it is a threaded type or locate the dimple that you need to push to remove the stem. Lay watch face down on a Selvyt cloth or movement dial side down on a piece of pithwood. Turn the screw counter clockwise three to four turns (screw does not need to be removed from the movement) or push the dimple as you Pull to remove the stem.


See our Guides: Removing a Watch Stem – Screw Type or Removing a Watch Stem – Push Button Type Removal





Hand-remove_step 3

Remove the movement ring, hands and then the dial. This is the first step to removing the old movement out of the watch case. Simply lift up on the movement ring where you see cut outs and be careful not to scratch any part of the movement with your tweezers or fingernail. Using a piece of pithwood place the movement on top of the pithwood then put a dial protector under the hands to protect the dial. Using a hand puller place over the hands and gently squeeze the hand puller and pull the hands off of the movement.


See our Guide: How to Remove Watch Hands


Click Here to Shop Our Watch Movements


Identify the Movement you Need


Now you need to look at your movement and see if there are any markings such as the manufacturer (Hattori, Miyota, ETA) and then look for a movement number. The Japanese brands are usually very easily identifiable as they are marked very clear on the movement (EX: VX42E, 6L12) If you are unable to find the movement number on the movement the Japanese will also usually make the movement number part of the case back and dial number. ETA movement numbers are usually on the very edge of the movement (EX: 955.1112, 210.011) or on the plastic movements under the cell in the battery well. These can be very hard to see and you will need to be very careful when ordering as being just one number off can change the diameter or features on a movement. (EX: 802.004, 802.104)


Replace a Watch Movement - nomenclature


To find a quartz watch movement to fit a mechanical can take a bit more work. There are several things that you will have to look for and measure. First look under the balance wheel (The circular piece that looks like it has hair wound around the middle) to see if there are any symbols and numbers. (EX: AS in a schield, number 1977-2) Your watch movement supplier may sometimes have a listing for a good replacement that can save you some time. Next determine the shape of the movement, round rectangular, oval etc. Measure the diameter of a round, the width and the length on the ovals and rectangulars. Next measure the thickness of the movement.

Calendar and Date Features
When you are ready to work in a watch, you should consider if the watch has second hands or if the watch has a calendar feature. If it has a calendar window, it is located a 3 o’clock, 4 o’clock or 6 o’clock. You also have to be aware of how thick the dial is because sometimes the same movement has a long and short center shaft. The calendar wheel can be replaced, so if you do not find the same movement with the calendar at 6 o’clock, you’ll have to remove the old calendar wheel and replace it in the new movement.

Now look at the dial to see if it has a calendar for the date, if it does, you had to make sure that a calendar can be seen through the window. Does it have second hand? Where is the second hand located? Is it removed, for example, at 6 o’clock. If that is the case, our choices are very limited, some movements can have a matching calendar, but the second hand at 6 o’clock will have to go. You can’t have both.

See our guides: Watch Movement Identification and Watch Case Number Finding Guide


Replacing the Movement

Mechanical to Quartz Watch Movement

Replacing a mechanical watch movement with a quartz watch movement is always more complex, takes more time, and can cause several more difficulties than replacing a quartz movement. Most problems arise from the size difference of old mechanical (large) to new quartz (small) movements. If you pick a thinner quartz movement over the old mechanical there is a good chance that the hole where the stem goes outside the watch case may not align properly. (This will also cause the dial and hands not to fit properly) This is a very difficult or impossible situation that will require a professional watchmaker.


If you have a mechanical watch movement and you would like to replace it with a quartz watch movement – remove the old movement from the case, measure it, and let’s say its 17.5 milliliters round, by 4.75 mm thick. Ideally, you would match the same dimension to make the new movement fit right. If you cannot find a movement that is the same size, you can use a watch movement as close as possible to those dimensions and use other tools and parts to make the movement fit correctly.


You need to know how thick the dial is because the center shaft comes in different lengths and the watch hands will not fit on correctly in the end if you do not know the thickness. You also want to make sure when you place the movement in the dial that it would have enough space around the hour hand and the minute hand to be set.


When replacing mechanical watch movements, keep in mind:


  • With mechanical watches you will always need to replace the watch hands because the old hands are heavy steel that will not work with quartz movements.
  • You will need to take more effort in finding a close replacement size and then finding a good fitting movement ring to secure the quartz movement in place.
  • You almost always have to use dial spots on mechanical movements because the dial feet will not match up (exception when you refinish the dial).
  • You will likely need to replace the watch stem forcing you to also get a new watch crown. (A stem extender can help change the size of the new stem to fit the original old crown).
  • If the dial is curved you will need to choose a new quartz movement with a very high center post because the movement will not fit flush to the dial causing the hands not to fit properly.


Quartz to Quartz Watch Movement

If you are replacing a quartz watch movement with another quartz movement you can usually find an exact replacement with no need for dial, hands, movement ring, stem, and crown.

Let’s say you have a good match, a movement smaller than the original, but with a calendar that fits, and a center shaft the goes fine with the dial so you know you will have a good match.


Attaching the Dial

Attaching the movement to the dial (the dial is the face of the watch) is very important for a long term fix and you have two choices for attaching the movement onto the dial depending on the design, your abilities, and what results you are looking for.


  • Finding a direct replacement movement that will fit the dial feet (the dial feet are two small metal posts that are inserted into the movement)
  • You can secure the movement to the dial with adhesive dial dots or use little glue dots. First the dial feet will need to be removed so you clip the original dial feet and make sure the surfaces is clean and smooth. Place the dial dots on the movement in a place that is safe, and press movement and dial together.


Using dial spots and glue is very convenient and quick when you cannot find a dial that matches the movement holes but the downfall is that with time and much wear, these shortcut fixes can come loose causing the movement to shift and cause further problems.


Dial Refinishing

If you need dial repair, you can send the dial into a dial refinishing company or through Esslinger Company. At the time of refinishing, you can instruct them to set the dial feet in a new position so that it will fit any movement. (so you would say that the feet need to fit an ETA 955-112 for example) You should make that information very clear and that is also one of the reasons that you should let a customer know, his/her watch will be done like the original manufacturer fitting perfectly and looking new. Now that you have the dial feet in the right place for the new movement and you have the new movement you are ready to insert into the watch case.

Dial refinishing before and after

Setting the Watch Hands

After the dial is set, you can place the watch hands onto the post. Using a sharp tweezers, carefully place the hands over the posts in order (Hour, Minute, Second). Use the watch crown and set the correct time, you should be sure the hands are not touching each other (or the dial). Wait at least after 24 hours to make sure the hands move freely before you use the watch.


MovementReplace-OD-of-crownReplacing the Watch Stem and Crown

When you purchase a new watch movement, it will usually include a watch stem, a temporary plastic crown, and the battery. To replace the old stem and crown, measure the old stem in millimeters, then cut the new stem down to the same size (using a side cutter and then tapering with a file) Thread the new stem onto the end of the watch crown. When you order a new movement, you might want to consider ordering two stems – then, if you cut the first one wrong, you will not have to order another one.

See our Guides: Removing a Watch Stem – Screw Type or Removing a Watch Stem – Push Button Type Removal



Watch movement ringMovement Ring Replacement

In the example , the movement is almost 2 milliliters thinner that the original that you are replacing, so you have to compensate for the movement thinness and it is also smaller in diameter. When doing that you have to look for a movement ring that will secure the movement in the watch case and prevent it from moving around loosely. A tight fit will not only help the watch work better, it will prevent possible damage that can occur so easily in wrist watches.


To help you have a good choice of movement rings for use with retrofitting many types of mechanical and quartz watches you can purchase the Movement Ring Assortment or you can make our own if you have some extra plastic movement rings. Hold the watch movement in place inside the watch case and compare each plastic movement ring to see which is nearest to the size, shape, and thickness of the new movement. The movement ring should hold the watch movement firmly in place with no play, but should not be pressing on sensitive electronic or mechanical parts of the watch movement.


Movement rings are made of a soft malleable plastic and can be formed and bent after getting to know the material. A good watchmaker can heat up the plastic and make some adjustments to make it fit quickly. Most movement rings need to be cut or trimmed on the outer edge to fit snuggly into the watch case and trim the top and sides (with sandpaper, jewelers files, dremmel machines)


MovementReplace-watch_back_hand_pressedClosing the Watch Back

Depending on the type of watch back that you are closing, be sure that the back does not touch the movement ring before closing. Be sure to check the condition of the back gasket before you close the watch as this is a very easy time to replace it and keep your new movement free of dirt and moisture. Depending on the type of watch back again (screw back, pressure fit, 4 screws) you will pressure fit or use the same tools that you used to remove the watch back.


See our Guide: How to Close a Watch Back









Sometimes when you change a movement from mechanical to quartz, not only you have to measure the diameter of the movement, the thickness, but also you have to consider the stem and crown, in some watches the case and the back are cut in a way that is not really an issue. But if the case has a tube or small hole where the stem goes; you have to make sure that the new movement will line up with that tube or hole. Also, if the case of the watch has a guard that protects the crown, you had to make sure that the new crown will fit between those guards.


Click Here to See Our Full Selection of Watch Tools




Share Button

You May Also Like...

  • How to Remove Watch HandsHow to Remove Watch Hands
  • How to Close a Screw Down Case Back with a Case Opener BallHow to Close a Screw Down Case Back with a Case Opener Ball
  • How to Close a Screw Down Case Back with a Case WrenchHow to Close a Screw Down Case Back with a Case Wrench
  • Energizer Watch Battery Replacement GuideEnergizer Watch Battery Replacement Guide
  • How to Remove a Stem – Screw Type Stem RemovalHow to Remove a Stem – Screw Type Stem Removal
  • How to Press a Bezel Fit Watch Crystal into Place with a Watch Crystal PressHow to Press a Bezel Fit Watch Crystal into Place with a Watch Crystal Press
  • How to Change a Watch BatteryHow to Change a Watch Battery
  • Quartz Clock Movement Parts and Assembly DiagramQuartz Clock Movement Parts and Assembly Diagram


  1. Rees Marshall, November 24, 2015 at 4:30 pm:

    Re Changing Quartz watch battery:
    Is there any truth in suggestions that the Pos & Neg pins need to be shorted to enable a quartz watch to function after changing a battery? I ask because mine watch is playing up.

    • Esslinger.com, November 24, 2015 at 5:02 pm:

      This is absolutely true. specifically on brands like Casio and other electronic wrist watches; without a restart, the watch will not run.

      • Rees Marshall, November 24, 2015 at 6:37 pm:

        Please specify Reset procedure

        • Esslinger.com, November 24, 2015 at 7:23 pm:

          This video shows the process (at 8:14) https://youtu.be/R6JbrVDqR7w

          • Rees Marshall, November 24, 2015 at 8:14 pm:

            I am really impressed that you answer my Qs, but the Video helps only a little as my ETA 956.032 has a basic PCB and I see Neg and Pos pads but NO AC Pin. There’s an arrow pointing away from Pos towards a spring loaded pin, is this part of the battery reset or the Stem releasing Pin? Also, the correct battery (634) sits tightly in the opening and is hard–up against a side-plate which does not press down on the battery?

          • Esslinger.com, November 24, 2015 at 8:42 pm:

            This movement does not require a reset after a battery change. There is another problem with the movement or a battery that will need to be investigated. There is a multitude of possible issues that could be the problem in this electronic / mechanical watch movement, we can provide the tools to inspect and diagnose this but we do not have an exact answer for what is happening with your watch.

          • coinfinder, August 21, 2016 at 4:16 pm:

            if you do not see an AC symbol on the movement then it does not need to be shorted out. Mostly digital or analog and digital have the AC feature. As for your ETA movement, I’m guessing it has a bad coil. That is just my first guess. This is a common problem that is easily fixed. Assuming you can get the coil. My email is JPRATT420024@YAHOO.COM. email me and I can go over it with you more. If you know electrical at all then a vault meter will tell you if the coil is bad or not. I had a movado I bought 10 years ago and never wore. when I put a battery in it did not work after no use and sitting for 10 years. I had a spare coil so I put it in and it worked rate off. Was a very easy fix as long as you can take your time and understand how a watch works. Email me if you want more help

      • thomachuck, April 4, 2016 at 11:51 pm:

        Not sure whether your advice to short out the pins applies to all electronic watches, to rechargeable watches only, or to these Casio models only (not clear). I have a Remington analog watch that does not use a rechargeable battery. Would I need to short out the pins in replacing the battery on this watch? It is an SR916SW battery.

  2. Siper2, January 16, 2016 at 10:15 pm:

    Hi, thanks for this! I have a Fossil JR-8561 case with a Ronda movement. The number looks like “515” maybe? There are several models on your site, any advice on which movement in particular?

  3. EEH, July 21, 2016 at 1:54 pm:

    Hello. I have purchased a second had omega speedmaster without a movement. Is it possible to find one that fits,
    knowing it has a chronometer ? Thank you !

  4. Chen Weizhong, November 7, 2016 at 12:08 am:


    Thanks for the great article. May I check if movements are universal in size? I’m anniversary present watch died on me and I was wondering if I could replace the movement with a working one from another watch.
    Would appreciate your kind advice on this. Rgds!


    • Esslinger.com, November 7, 2016 at 3:18 pm:

      Movements are not universal in size. Replacing the movement is possible but you will need to do some measuring and looking up the model and numbers. Check this article for more information: http://blog.esslinger.com/identifying-watch-movements/

      • Chen Weizhong, November 9, 2016 at 3:15 am:

        Many thxs for the great help!

  5. Gopalakrishnan Ramaswamy, December 11, 2016 at 3:11 pm:

    whether all auto winding mechanical watches need `clutch wheel` especially the ones with Day&Date?Please help me.
    (and particularly Citizen` Eagle`series and SEIKO 6619A

  6. Randi Ka Ashiq, March 27, 2017 at 9:32 am:


    very informative post. I really appreciate you having written it. I was actually looking for replacement of an ETA trendline F06.111 quartz movement for my watch.

    Can you suggest some 1 to 1 equivalent in Miyota, Epson, Hattori or anything else ?

    F06.111 is a 3 hands with calener. Specs are : thickness 2.50 mm
    dia 25.60 mm and size 11-1/2. The calender is at postion 3 O Clock

    Many thanks

    • Mark Esslinger, May 9, 2017 at 5:52 pm:

      Try – Ronda 715 (HQ715) .15mm thicker, same hands, same tap, same dial position but cannot guarantee the date will line up. You will have to cut the new stem to the correct length to fit.

  7. Randi Ka Ashiq, March 27, 2017 at 9:39 am:


    very informative post. I really appreciate you having written it. I was actually looking for replacement of an ETA trendline F06.111 quartz movement for my watch.

    Can you suggest some 1 to 1 equivalent in Miyota, Epson, Hattori or anything else ?

    F06.111 is a 3 hands with calender. Specs are : thickness 2.50 mm
    dia 25.60 mm and size 11-1/2. The calender is at postion 3 O Clock

    I was considering VX42E.

    Please let me have your expert advice.
    Many thanks

    • Esslinger.com, March 27, 2017 at 3:17 pm:

      I would opt for the ETA 955.112 which is the high grade version of the ETA F06.111
      Nothing in anther line as you would not know if the dial, hands, or calendar line up – the only possible other option is the Ronda 715 depending on your overall height, same thing for the 955.112. Hope this helps.

      • Randi Ka Ashiq, March 28, 2017 at 4:53 am:

        Great !!! Thanks a lot for
        a quick reply. 955.112 is a good option suggested by you.

        Many many thanks.

        I am in India. If I order on you. Can you send it by simple airmail without pasting a bill onthe envelop as it can get stuck at Indian customs.

  8. Jon-Michael Payne, April 26, 2017 at 4:03 pm:

    I’m replacing a mechanical movement with a quartz movement. When the dial is curved and you need to install a movement with a very high centre post, what would you recommend to install between the dial back and the top of the movement?

    I need to clear at least 1mm so the stem lines up with the case tube (and avoids the dial edge).

    I first thought of using some sort of 1mm thick double sided tape… but that would be spongy and easily damage the movement if I needed to reposition it.

    how do you shim the gap?

    • Mark Esslinger, May 9, 2017 at 7:03 pm:

      I do not think you need to install anything and should opt for a higher posted movement to allow for the clearance for both the hands and the crown